COD.: DMR-100
Single-color LED strip dimmer 12/24V - 10A - Opto-isolated push-button control
Descrizione
Single-color LED strip dimmer 12/24V - 10A - Opto-isolated push-button control
Single-color dimmer for LED strips and resistive LED sources at constant voltage 12V or 24V. Brightness control is performed via a generic push-button properly installed at the PP terminals. Push-button not included.
The device retains memory of the last operating mode set even after power off and on.
Specifiche Tecniche
| Input Voltage | 12/24 Vdc |
| Max Power | 120W (12V) / 240W (24V) |
| IP Rating | IP20 |
Applicazioni
The device described in this instruction sheet is intended to be installed in lighting systems to control single-color 12/24V LED strips via an externally connected push-button for civil/residential/commercial indoor applications.
Modalità d'Uso
The load connected to the DMR-100 controller output can be turned on or off with a single short press of the push-button.
It is also possible to vary the brightness of the load with a long press.
Click: on/off.
Long press from on: increase/decrease intensity. Minimum brightness: 2.5% (not adjustable).
Long press from off: turn on "courtesy light" mode (Default 10%). This intensity is adjustable (setting a value between 2.5% and 10%).
Procedure to change "Courtesy light" brightness intensity.
1. Turn off the dimmer.
2. Hold the push-button and simultaneously power the dimmer.
3. Use long presses to select the desired intensity.
4. Complete the save by briefly pressing the push-button. The connected LED strip will emit two flashes to confirm the change.
Note: the device retains memory of the last operating mode set even after power off and on.
State Short press Long press
OFF ON at previously stored intensity "Courtesy light" mode
ON, Dimming OFF Intensity variation
ON, Courtesy light OFF No effect
Istruzioni di Connessione
Disconnect mains power on the line where the module is to be installed.
Connect the DMR-100 dimmer to a 12 or 24Vdc power supply of adequate power at the 2-pole terminal block marked "Vin +/-".
Connect the load (LED strip) to the "Vout +/-" terminals of the terminal block.
Connect the push-button between the "Push N.O." terminals.
Reconnect mains power.
Maximum allowed cable length to the push-button is 10m.
It is possible to connect multiple push-buttons in parallel.
AVVERTENZE:
To prevent personal injury and device damage caused by electric shock, users must observe the following safety tips.
Installation must comply with the regulations governing the installation of electrical equipment in force in the country where the products are used. In particular, the electrical system to which the line powering the device belongs must comply with the applicable CEI 64-8 standard. Said line must be easily disconnectable and adequately protected against overcurrents, direct and indirect contacts. An easily accessible disconnecting device must be incorporated into the properly installed electrical system.
The product must be installed inside an electrical panel.
Installation and maintenance must be performed by a qualified electrician.
This product contains sensitive electrical components that may be damaged by electrical spikes, overvoltages, electric shocks, discharges, etc.
Before installation, carefully inspect the circuit and eliminate any potential hazards.
Do not work under voltage. Disconnect power before installation and/or maintenance.
The device is not designed for outdoor use. Use in dry, clean environments free of corrosive gases and strong electromagnetic interference.
Leave adequate space around the device for proper air circulation. Maintain adequate distance and do not stack with other devices.
Do not place near heat sources. Do not expose to direct sunlight or extremely high temperatures.
Install the device in dry, clean locations. Avoid contact of surfaces with liquids, detergents, and oils.
Use in environments with humidity below 90%.
Handle the device carefully to avoid violent vibrations that could affect performance.
If any anomaly or malfunction occurs, the user must stop using it.
To avoid the risk of electric shock, do not open the housing.
In case of failure, contact an authorized technician.
Ensure the operating voltage matches that indicated on the device.
Install an adequate input fuse according to the connected load (LED strip).
The power supply must be selected based on the LED load used, for voltage and current.
Use a power supply with nominal power greater than the load to be powered (at least 30%).
The load power connected to the device must not exceed the rated nameplate data.
Overloads, electrical arcs, and short circuits can irreparably damage the device.
Do not connect the device outputs in parallel. Do not use the device for purposes other than those prescribed.
Using excessively long connection cables may compromise normal operation. Check maximum cable length and size cable sections according to the connected load.
Do not clean with a damp or wet cloth.
Informazioni Importanti:
Read this installation guide carefully before using the product. This manual provides basic information about the DMR-100 device regarding safe use. Below are instructions for installation and proper operation.
The device described in this manual is intended only for the use for which it was expressly designed (see Applications/Use). Any other use is considered improper and dangerous. Keep this instruction sheet.
Note Tecniche
Acme Corporation S.r.l. reserves the right, in compliance with applicable regulations, to make technical and dimensional changes to improve the characteristics and performance of the product without prior notice.
Limitazione di Responsabilità
The installation, use, and maintenance of the device code DMR-100 (hereinafter referred to as "device") are the sole responsibility of the user. Acme Corporation S.r.l. is not responsible for any direct or indirect damages arising from the use or malfunction of the device.
Acme Corporation S.r.l. declines all responsibility if the device is damaged due to human factors causing damage, injury, or loss.
Acme Corporation S.r.l. declines all responsibility for damages or injuries arising from improper use or lack of maintenance of the device.
Acme Corporation S.r.l. is not responsible for any type of damage, whether direct or indirect, moral, incidental, special, or consequential, such as data loss, business interruptions, or financial damages. The liability of Acme Corporation S.r.l. is limited to the purchase price of the device. It is recommended to carefully follow the instructions provided in the manual. It is important to comply with local regulations and follow specific instructions for installation and use.
Garanzia
Device guaranteed for 24 months against any defect due to materials or manufacturing. Any warranty is void in case of improper, incorrect, or negligent use of the device or any tampering. The defective product must be returned to the retailer for repair. The warranty is valid only if the device is accompanied by a fiscal receipt or invoice.
Smaltimento: The crossed-out wheelie bin symbol, in accordance with Directive 2012/19/EU (EN62321:2009), shown on the device indicates that the product, at the end of its useful life, must be disposed of separately from household waste and taken to a collection center for electrical and electronic equipment. For information on collection points for end-of-life equipment, contact your local municipality or waste disposal services.
Conformità: This product bears the CE mark in compliance with the provisions of the directives:
Directive 2014/30/EU for Electromagnetic Compatibility
Directive 2014/35/EU for Electrical Safety.
Directive 2011/65/EU, 2015/863/EU on the restriction of hazardous substances in electronic devices (RoHS).
Directive 2012/19/EU on waste electrical and electronic equipment (WEEE).
For more information visit www.example.com
The user is prohibited from making any changes or modifications of any kind to the device. Changes or modifications will void the product's compliance with the above standards.